• Safety gear and proper tools must
be used. Failure to do so can result in
property damage and/or serious injury.
• A minimum of two people are required
for this installation. Do not attempt
to install this mount alone under any
circumstance.
1 Important
Take time to read this manual before you
use your wall mount. It contains important
information and notes regarding operating your
wall mount.
• Follow all instructions and
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved. Reproduction in whole or in
part is prohibited without the written consent of
the copyright owner. Trademarks are the
property of Koninklijke Philips Electronics N.V.
or their respective owners.
recommendations regarding adequate
ventilation and suitable locations for
mounting your display. Consult the
owner’s manual for your display for
more information.
• This mount is equipped with a safety
device that must be used whenever
the mount holds a display. Not using
the safety device can cause property
damage, serious injury, or death.
BWarnings
• Make sure these instructions are read
and thoroughly understood before
attempting installation. If you are
unsure of any part of this installation,
contact a professional installer for
2 Your fixed wall mount
assistance or contact Customer Service Congratulations on your purchase and welcome
at 1-919- 573-7854.
to Philips!
• This product has been designed
for application on a vertical wall in
commercial and residential buildings,
constructed of wood wall studs or
masonary (solid concrete, brick, and
stone). If you are unsure of your wall
To fully benefit from the support that Philips
offers, register your product at
Designed to fit most TV brands with a focus
composition or for assistance with other on safety and ease of use. Includes Easy 1-2-3
surfaces, contact a qualified installer.
• This product is not designed for use on
walls constructed of metal studs. If you
are unsure of your wall composition
or for assistance with other surfaces,
contact a qualified installer.
installation kit, complete with: all necessary
hardware for mounting on different types of
walls, mounting templates and bubble level. C-UL
US listed for weight capacity up to 132lbs.
• The wall or mounting surface must be
capable of supporting the combined
weight of the mount and the display;
otherwise the structure must be
reinforced.
• Do not exceed the maximum load
capacity of 132lbs for this product.
• Fits 30-55” screens
3
2.1 What’s in the box.
Wall mount
Bag #1
Cotter pin
(A) M4x12 Bolt (x4)
(B) M4x30 Bolt (x4)
(E) M5x30 Bolt (x4)
(H) M6x35 Bolt (x4)
(K) M8x40 Bolt (x4)
(N) Large Spacer (x4)
(Q) M8x63 Lag Bolt (x6)
(C) M4 Lock Washer (x4)
(F) M5 Lock Washer (x4)
(I) M6 Lock Washer (x4)
(I) M8 Lock Washer (x4)
(O) M6 Washer (x4)
Bag #2
Bag #3
Bag #4
Bag #5
Bag #6
(D) M5x12 Bolt (x4)
(G) M6x12 Bolt (x4)
(J) M8x16 Bolt (x4)
(M) Small Spacer (x4)
(P) Concrete Anchor (x6)
(R) Lag Bolt Washer (x6)
2.2 What you’ll also need.
• Phillips head screwdriver
• Ratchet or driver with 1/2” (13 mm) socket
• Portable or electric drill
• 1/4” (6 mm) drill bit and stud finder for drywall installation
• 3/8” (10 mm) masonry bit for concrete installation
• Stud finder
4
4
5
With the help of another person, place the
mount against the wall and level it using the
bubble guide.
While another person holds the mount in
place, mark four locations (two per stud)
on the wall where the mount is to be
installed. Be sure to use the center of each
stud. (these marks should line up with
the ones made in step 3 above using the
template).
Set the mount aside and drill a 1/4” (6 mm)
pilot hole at each marked location.
Place the mount back against the wall and
secure it using the lag bolts (Q) and lag bolt
washers (R) provided. Do not over-tighten
these bolts and do not release the mount
until all bolts are in place.
Once all (4) lag bolts are in place you must
tighten each one. (note: be sure not to over
tighten). 1
3 Installing your wall mount
In this chapter, the basic steps to get you started
are described.
B Warning
Carefully read the safety precautions
in “Section 1 Important” before you
install the wall mount.
6
7
3.1 Mounting the wall plate (drywall)
B Warning
For safety reasons, this mount must
be secured to two adjacent wood
studs at least 16” apart.The studs
must be capable of supporting the
combined weight of the mount and
display.
8
1
1
2
See enclosed mounting template for
diagram and guide of how to mount
properly on the wall.
Using a stud finder, locate and mark two
adjacent studs for securing the mount
(make sure your marks are in the center of
each stud).
3.2 Mounting the wall plate (concrete)
D Note
Once studs have been located you will
need to verify with a hammer and a
nail
B Warning
For safety reasons, the concrete wall
must be capable of supporting the
combined weight of the mount and
display.
A) Simply place the nail over your
mark on the wall and tap in with
hammer. if the nail encounters
resistance and is secure in wall you
have verified a stud location
B) If it just pushes through with no
resistance you will need to start
over and locate the stud.
Using the enclosed mounting template,
place the diagram against the wall and mark
four locations (two per stud) on the wall
where the mount Is to be Installed. Be sure
to use the center of each stud.
1
2
See enclosed mounting template for
diagram and use enclosed mounting
template as a guide for precision mounting.
Using the enclosed mounting template,
place the diagram against the wall and mark
six locations on the wall where the mount
Is to be Installed.
3
5
3
4
5
6
With the help of another person, place the
mount against the wall and level it using the
bubble guide.
While another person holds the mount in
place, mark six locations on the wall where
the mount is to be installed.
Set the mount aside and drill a 3/8” (10
mm) pilot hole at each marked location.
Remove any excess dust from the holes.
Insert a concrete anchor (P) into each hole
so that it is flush with the concrete surface.
A hammer can be used to lightly tap the
anchors into place if necessary.
3.3 Attaching the arms to the display
B Warning
Use extra care during this part of the
installation.Avoid laying your display
face down if possible as it may damage
the viewing surface.
1
Examine the back of your television.
If the back of your display is flat: You
will be using one of the shorter bolts from
the hardware kit.
3
7
Place the mount back against the wall and
secure it using the lag bolts (Q) and lag bolt
washers (R) provided. Do not over-tighten
these bolts and do not release the mount
until all bolts are in place. 2
3
2
If the back of your display is curved
or recessed: You will be using one of the
longer bolts and a spacer.
4
4
8
Once all (6) lag bolts are in place you must
tighten each one. Be sure not to over
tighten.
D Note
If the concrete wall is covered
by a layer of plaster or drywall,
the concrete anchor must pass
completely through the layer to rest
flush with the concrete surface.
2
Determine the correct diameter bolt to
use by trying one bolt each from Bags 1
- 4 of the hardware kit. Do not force any
of the bolts – if you feel resistance stop
immediately to avoid damaging your display.
6
3
Attach the arms to the back of your display
using the bolts identified in Steps 1 and
2 and the corresponding lock washer
(C, F, I, or L).You will need to use the M6
washers (O) if you are using the M4, M5,
or M6 bolts. If your display has a curved or
recessed back, you may also need to use a
spacer (M or N).
4 Mounting and adjusting
1
With the help of another person, carefully
lift your display and place it on the wall
plate. Do not release the display until the
mounting arms have securely hooked onto
the mount.
6
4
Make sure the screws are snug, but do not
over-tighten. 5
6
5
2
Carefully hook the display onto the wall
plate 7
E Tip
Use a longer bolt and spacer for
7
displays with curved or recessed
backs. Do not use the M6 washer (O)
if you are using the M8 bolts (J or K).
B Warning
Insert the safety bar at the center of
the mount to avoid having the display
accidentally knocked off the mount.
3
This MUST be done in order to secure
the display to the mount. NOTE:A cotter
pin (included) Is used to secure the arms
to the mount OR a padlock (not included)
can be inserted into the hole at the end of
the saftey bar to help prevent theft of your
display. A small cotter pin can be used to
secure your display to the mount. (included)
7
4
Once the tv is fitted properly on to the wall
bracket, the security bar must be put into
place. 8
5 Guarantee and service
Please contact Philips directly if you have any
questions in the installation process of the wall
mount. Call 1-919-573-7854.
8
Limited One-YearWarranty:
Philips warrants that this product shall be free
from defects in material, workmanship and
assembly, under normal use, in accordance with
the specifications and warnings, for one year
from the date of your purchase of this product.
This warranty extends only to the original
D Note
Slide arm through slots in wall plate & purchaser of the product, and is not transferable.
brackets
To exercise your rights under this warranty, you
must provide proof of purchase in the form of
an original sales receipt that shows the product
name and the date of purchase. For customer
support or to obtain warranty service, please
call 1-919-573-7854.THERE ARE NO OTHER
EXPRESS OR IMPLIEDWARRANTIES. Philips’
liability is limited to repair or, at its sole option,
replacement of the product. Incidental, special
and consequential damages are disclaimed where
permitted by law.This warranty gives you specific
legal rights.You may also have other rights that
vary from state to state.
5
6
Once the security bar is slid into the
appropriate slots, a lock(not provided) may
be placed for additional security.
A small cotter pint can be used to secure
your display to the mount. (included). 9
9
Register your product and get support at
8
© 2009 Koninklijke Philips Electronics
All rights reserved.
SQM5822_27_UM_V2.0
|